Search/Sub head 16/16.102

16.102Providing and fixing factory made intermediate and straining Y-arms, consisting of MS angle 50 x 50 x 5 mm as per IS 2062, each arm of length 510 mm angled at 120° having 3 nos. of slots of 6 mm width at an angle of 45° and 12mm diameter hole at the end of slot at a depth of 25 mm, welded with (i) at top and at bottom with a cap consisting of 45 mm long sleeve of 83 mm outer diameter and 79 mm inner diameter of 2mm thick MS plate in intermediate Y-arm and (ii) a 3 mm thick 63 mm outer diameter, 100 mm long MS pipe welded with 76 mm diameter, 5 mm thick MS plate in straining Y-arm, having two sets of 14 mm diameter holes in sleeve / pipe for inserting SS 316 mushroom head bolts with breakable head safety nuts of size M8x120 mm. The Y-arms shall be hot dip galvanised coating of minimum 460 GSM as per IS 4759 and thermoplastic powder coating of minimum 400 microns as per coating standard EN 10245 -1 and ISO 12944 (as applicable) of specified colour. Intermediate Y-arm shall be provided at 2.50 m centre to centre and straining Y arm shall be provided at first post, every 16th post, last end post and corner post. Six numbers of 3.50 mm diameter SS 316 Razor wires as per IS 6911 of tensile strength of 1400-1700 N/Sqm with SS 316 Tear blades (TBBT) of size 30 mm x 16 mm x 0.47 mm at 50 mm centre to centre in slots of Y-arms and tightened using six SS 316 Eye bolts at every straining Y-arm. SS 316 Razor wire punched tape coil wire 3.5mm diameter as per IS 6911 of tensile strength 1400-1700 N/sqm having diameter 850 mm of 56 loops stretchable length 10 m shall be spread over the six Razor tape wire and tied with SS 316 hog rings of diameter 3 mm with minimum 8 numbers per meter length of fencing complete as per direction of Engineer-in-charge. Coating requirements:- The modular fence manufacturer shall have a facility for surface preparation of (Blast clean SA 2.5) and surface treatment (7 tank or 10 tank process) for better longevity of the coating. Type Test Certificate should be provided by the Fence Manufacturer for the quality of powder coating and thermoplastic coating during supply of fence materials. Type Test Certificate should be from a Government Institution like Central Electrochemical Research Lab. The Fence Manufacturer shall have a valid applicator certificate for thermoplastic powder coating.

Matches DSR 2023

Rate per metre

1,779.85

DSR 2023

How this rate is built12 items, 4 additional charges

MaterialSS 316 Razor wire concertina coil 3.5 mm Φ- 850 mm dia, SS 316 Razor Tape wire 2.5 mm including wastage @ 5%, Straining Y-Arm of angle of size 50x50x5 with cap of plate 76 mm dia and 5mm thick and pipe 65 nominal bore 100 long with coatings, SS 316 Eye bolt with nut and washer, SS 316 Hog rings (i.e. 8 ring per m), Intermediate Y-Arm of angle of size 50x50x5 with cap of 45mm long sleeve of 83mm dia 3mm thick inner. Coatings, Mushroom headed M8x120 bolt & nut with washer

LabourBlacksmith 2nd class, Beldar, Assistant Fitter or 2nd class Fitter

Loading

Water 1%GSTCPOH 15%Cess 1%

View full rate analysis

See every quantity and rate, and the 4 additional charges with the amount each one is worked out on. Change any rate to see the updated cost, then download the complete working as an Excel file.

Sign in and unlock 3 items free See prices

Near this item in the book

16.101Providing and erecting factory made high security welded wire mesh panels of size 2667 mm x 955 mm, weight 24.3 kg of each panel, having mesh size 76.2 mm x 12.7 mm produced by electrical resistance welded galvanised wire of diameter 4.00 mm of grade 1 to 4 as per IS:7887 , with zinc coating of 100 GSM as per IS 2629 and IS 4826 (as applicable) and minimum 300 microns of thermoplastic powder coating as per coating standard EN 10245 -1 and ISO 12944 (as applicable) of specified colour including making two numbers V-shaped bends, each of depth 38 mm and width 150 mm, at an angle of 100° in horizontal direction of the panel with overlapping of panel (75 mm overlap in horizontal direction and 167 mm overlap in vertical directions). Fixing CHS post and wire mesh panel shall be done by using Omega clamp of size 180 mm x 35 mm x 3 mm with 2 nos of 12 mm dia holes and profile cover plates of size 180 mm x 50 mm x 2.75 mm with 2 slots for bolts, using two numbers SS 316 mushroom head bolts with breakable head safety nuts of size M8 x 80 as per IS 8535-1987 and SS 316 washers of size 15.89 mm outer diameter, 8.38 mm inner diameter and 2.04 mm thick and 2 nos of IP binders (set of 2 plates) are used in overlapping area of panels, made up of MS flat 25x5mm size and 160mm long with 2 slots of 9x20mm and fixed with 2 nos. SS 316 M8x35 mm size mushroom head bolts. Omega clamp and IP Binder, both shall be made up of MS flat as per (Omega clamp as per IS 277 and IP Binder as per IS 2062) which shall be hot dip galvanised for minimum 360 GSM coating as per IS 2629 and IS 4759 (as applicable) and thermoplastic powder coating of minimum 400 microns of as per coating standard EN 10245 -1 and ISO 12944 (as applicable) of specified colour all complete as per direction of Engineer in charge. No extra cost shall be paid for permissible overlapping of panel. However extra overlapping of panel as per site requirement if any beyond above mentioned shall be paid additionally. Coating requirements:- The modular fence manufacturer shall have a facility for surface preparation of (Blast clean SA 2.5) and surface treatment (7 tank or 10 tank process) for better longevity of the coating. Type Test Certificate should be provided by the Fence Manufacturer for the quality of powder coating and thermoplastic coating during supply of fence materials. Type Test Certificate should be from a Government Institution like Central Electrochemical Research Lab. The Fence Manufacturer shall have a valid applicator certificate for thermoplastic powder coating.

16.102This item

13.117(i)6 mm thick · Providing and applying Ready Mix Plaster of approved brand and manufacturer, having minimum compressive Strength of 6.0MPa, of specified thickness in one coat on new/old surface of walls/ceiling, using factory produced, pre-blended, premixed, formulated ready-mix mortar supplied in dry form requiring only the addition of water at the site before start of application, and including applying Portland cement slurry @0.40Kg/Sqm applied on hacked/uneven background such as bare brick/CC and Block/RCC surface after preperation of surface etc. complete as per manufacturer's specification finished in smooth line and level at locations and all floors.

13.117(ii)12 mm thick · Providing and applying Ready Mix Plaster of approved brand and manufacturer, having minimum compressive Strength of 6.0MPa, of specified thickness in one coat on new/old surface of walls/ceiling, using factory produced, pre-blended, premixed, formulated ready-mix mortar supplied in dry form requiring only the addition of water at the site before start of application, and including applying Portland cement slurry @0.40Kg/Sqm applied on hacked/uneven background such as bare brick/CC and Block/RCC surface after preperation of surface etc. complete as per manufacturer's specification finished in smooth line and level at locations and all floors.

13.117(iii)15 mm thick · Providing and applying Ready Mix Plaster of approved brand and manufacturer, having minimum compressive Strength of 6.0MPa, of specified thickness in one coat on new/old surface of walls/ceiling, using factory produced, pre-blended, premixed, formulated ready-mix mortar supplied in dry form requiring only the addition of water at the site before start of application, and including applying Portland cement slurry @0.40Kg/Sqm applied on hacked/uneven background such as bare brick/CC and Block/RCC surface after preperation of surface etc. complete as per manufacturer's specification finished in smooth line and level at locations and all floors.